商务支持

技术支持

About Guangxun

关于光迅

Adding New Floors & Rooms to Hotel All-Optical Networks
2026-11-20 13:55:15 5

Adding New Floors & Rooms to Hotel All-Optical Networks

When a hotel adds new floors or guest rooms, the existing triple-network infrastructure is usually still in stable operation and cannot be shut down for expansion. This scenario adopts an add-only strategy: deploy independent all-optical branches only for the new zones, connect new rooms to the new system, and keep the original computer room and legacy devices untouched. Phones in new floors can interconnect with the original PBX via an O-port gateway, so the old system remains undisturbed. The expansion scope and access mode are subject to site survey and project design.

1. Expansion Status & Judgement Rules

For new-area renovation, we only add new hardware, without modifying any legacy systems.
The original AC+AP network, PBX voice system and IPTV service keep running normally even at full occupancy. We only need to cater for newly added floors and rooms — no replacement, no reconfiguration of old devices, old cables or existing phone numbers.

This approach applies when the hotel owns the legacy equipment and intends to keep the old network. It differs from full-scale migration of separated triple networks, as there is no replacement work and no impact on in-service guest rooms.

Why not connect new rooms directly into the old triple networks? That would require laying three separate sets of cables, expanding the computer room and adjusting the original PBX. Construction would spread to existing floors and disrupt checked-in guests. Deploying an independent fiber-to-room link for new zones confines all construction work to the new floors, minimizing service impact.

2. Implementation for New Zones

Install an O-port gateway in the core room to interface with the original PBX, and deploy vOLT or OLT on the same side to provision new PON branches.

First, add an O-port gateway in the core equipment room to connect to the existing PBX. Phones in new rooms communicate through this gateway, retaining the original numbers, service logic and internal dialing rules. Interconnection to the legacy PBX is essential for this expansion case; there is no need to rebuild the whole voice system.

Optical access for the new branch is also arranged here: add a vOLT module on the core switch, or deploy an independent OLT. The vOLT adds PON capability to the existing core switch, so the original switch can continue serving without replacement.

Run a new optical cable from the core room to the new floor, deploy a passive splitter on that floor, then split optical signals to each new guest room. Every new room is equipped with one optoelectronic AP and a wall-mounted phone. The new all-optical branch runs in parallel with legacy circuits on a zone-isolated basis. Notifications are only sent for the floors under construction, and rooms on existing floors operate normally.

3. Core Capabilities

A single optoelectronic AP converges three services in each room; passive splitters eliminate power supply and maintenance requirements on floors.
The in-room optoelectronic AP delivers internet, IPTV and voice services altogether. Wall phones connect back to the original PBX, so internal extension dialing stays consistent for staff.

The AINOPOL IP-POL Boundary-Free Solution delivers a non-intrusive expansion workflow: legacy systems are untouched. Only the O-port gateway and vOLT / OLT are added at the core to create a dedicated all-optical branch for new floors. Only these few devices are added to the rack, and the original cabinets and patch panels are preserved.

Passive optical splitters deployed on new floors require no power or heat dissipation. They can be installed inside weak-current boxes or wall-mounted, replacing power-hungry floor aggregation switches and cutting fault points. Splitting ratios and optical power budgets must be verified on-site. Optical power differences and port density on the new PON branch also require link-by-link validation, subject to site survey.

4. Rollback Rules & Future Evolution

Rollback relies on keeping legacy cables and devices until acceptance. The new optical foundation supports smooth migration of old networks later.

Rollback procedures must be documented: legacy lines and hardware remain online until acceptance. If the new branch fails, simply disconnect it, and the original network resumes service instantly without affecting occupied rooms.

Site survey also verifies core switch port availability, power & air conditioning capacity in the machine room, cable tray availability on new floors, quantity of endpoints and permitted construction windows. All final arrangements depend on on-site conditions.

The newly deployed infrastructure builds a ready all-optical foundation. When the hotel plans to renovate the old building later, legacy services can be migrated onto this same core platform seamlessly, without deploying another independent core system or re-running backbone fibers.
The optical layer is decoupled from end devices. Future upgrades from GPON to XGS-PON, 50G PON and Wi‑Fi 7 optical APs only require swapping terminal hardware, while intermediate fibers and splitters stay unchanged. Devices selected for the new floors are compatible with this upgrade roadmap.

Ownership and administrative permissions belong fully to the hotel for the new branch. VLAN configuration, port mapping and QoS tuning can be adjusted directly from the backend. Surveillance and access control systems on the new floors can be integrated freely, with no need to submit operator tickets for expansion.

To summarize, expansion for new floors and rooms is purely additive: deploy an O-port gateway at the core to interconnect with the original PBX, add vOLT/OLT for a new PON branch, install passive splitters on new floors and run fiber to each guest room, equipped with optoelectronic APs and panel phones.
The AINOPOL IP-POL Boundary-Free Solution keeps all legacy systems online, running old and new networks in parallel. Existing phone numbers are preserved, active guest rooms remain undisturbed, and the same core platform can accommodate old-building renovation in the future.

FAQ

Q: Will existing phone numbers change?
A: No. Phones in new rooms connect to the original PBX through the O-port gateway. Old numbers and dialing rules for internal extensions remain exactly the same.

Q: Does the legacy network need to be shut down?
A: No modification to old systems. New zones have dedicated optical cabling and splitters. The new branch runs separately from legacy networks, construction is restricted to new floors, and existing guest rooms stay online.

Q: Do we need to rebuild everything when renovating the old building later?
A: The new expansion has already deployed the all-optical foundation and core optical equipment. Legacy services from the old building can be migrated onto this same platform later, without building another independent core or re-laying backbone cables. The migration plan and scope will be confirmed by site survey.